CNC turning chips – shape and size, and ROI

CNC: Are you cutting optimally ? Your CNC turning chips can tell you !

Next time you’re in the shop floor,  just look at the CNC turning chips. They can tell you whether your machine is giving you a proper return on investment or being underutilized. The shape and size of chips can give you a rough idea of whether the correct cutting parameters are being used. CNC turning chips - cutting parameters

Width=Depth of cut. Thickness=Feedrate

The thickness of the chip is (almost) the feed rate.

Chips are not breaking ? The feed rate is too low.

The ideal chip is up to 40 mm. long, shaped like a 6 or a 9. If the machine is turning out long chips, the feed rate is too low. Half the feed rate means twice the cycle time. Long chips also mean machine idle time to clear the chips. Look at the tool manufacturer’s catalogue and find out the correct feed rate for the insert that is being used. This post tells you how to determine the feed rate range for proper chip breaking : https://cadem.com/cncetc/cnc-turning-chip-breaking/ CNC turning chips - short Chips breaking properly – correct Feed rate long steel chips improper feed rate

Chips NOT breaking properly – incorrect Feed rate

The width of the chip is the depth of cut If the spindle load is too low in roughing, the depth of cut is too small.

Increase the depth of cut to the maximum possible. Half the depth of cut means twice the cycle time. The depth of cut is the width of the chip. In rough turning or facing this must be such that the spindle power is being used to the maximum. If the spindle power meter shows less than 100 % in rough turning (on most shop floors it will be less than 50 %), there is scope for increasing the depth of cut. Check what shape and size of insert is being used, and look at the table in this post to get the maximum possible depth of cut: https://cadem.com/cncetc/rough-turning-depth-of-cut/

Pic. and text source: CADEM NCyclopedia multimedia CNC training software.

Idea bulb

Transform production and profits dramatically, in just a few months. With a CNC machine monitoring system.

Etc.

Steve Fossett – Superman

This is someone I find totally awe-inspiring. Steve Fossett was a US businessman who made a pile of money in Financial services, with two brokerage firms. At the age of 46 he decided that he’d got bored with the corporate life, and started off on a life of adventure. He set 116 records in five different sports, 60 of which still stood when he died at the age of 63. Most of the flying records were after the age of 58.

Ballooning : First person to fly around the world in a balloon in 2002. Set 4 distance and speed world records. In 2006, he broke the record for the longest flight, spending nearly 77 hours in the air and covering more than 40,000km. The winner in a distance race is the person who has travelled the longest distance in given conditions (e.g., nonstop and non-refueled), while in a speed race it’s the person who’s travelled the fastest.

Airship flying : World speed record in 2004.

Aircraft flying: Broke 3 world records (out of a possible 7). In 2007 (at age 63, the year he died) he made the first solo non-stop flight around the world without refuelling in 67 hours. In 2005 (at age 61) he re-enacted the 1919 first trans-Atlantic flight, in a replica of the original plane (with a non-pressurized cockpit).

Sailing : As skipper with a 13-member crew, he beat the round-the-world sailing record in 2004, completing the voyage in 59 days and nine hours. He set 23 speed records and nine distance records. Glider flying : 10 speed records. Record for highest altitude flight in a glider : 15,460 m. Mountain climbing : Fossett was a lifelong mountain climber and had climbed the highest peaks on six of the seven continents. Swimming : In 1985, he became the 270th person to swim across the English Channel on his fourth try. Car racing : Competed in the 24 hours of Le Mans road race twice. The race, held in France, is for 24 hours continuous (shared by 3 drivers in turn), and tests the endurance of the drivers and their cars. Completed the Paris to Dakar Rally a 4300 km. off-road endurance race through the North African desert, from Paris-France to Dakar-Senegal. Dog-sled racing : He completed the 1,875 km Iditarod Trail Sled Dog Race in Alaska, US, in which he finished 47th on his second try in 1992 after training for five years.

It involves racing through blizzards in whiteout conditions, sub-zero temperatures and gale-force winds which can cause the wind chill to reach -73 °C.

He survived all those incredibly dangerous things that he did, but died during a simple pleasure flight near his home town, in a single-seater plane. For him, his last flight was the equivalent of our walking across to the nearby grocery shop. For us, even this was an incredibly dangerous and adventurous thing to do.

Someone with absolutely zero fear of death ? What a life !

More info : http://en.wikipedia.org/wiki/Steve_Fossett